PILOT RC LASER V3 – 103″ \(2.61m\)

Time for a change! Pilot-RC has broken all the molds with this one.

The Laser has been fully designed from the ground up for out and out performance, keeping in line with current demand for faster, more aggressive and more agile models, while still keeping the well know great flying characteristics Pilot-RC models are known for.

SPECIFICATIONS :
Model: Laser – 35%
Wingspan: 101.8″ \(2.587mm\)
Length: 99″ \(2.514mm\) with 5″ spinner
Wing area: 1,771 "² \(11,430 cm²\)
Weight: 26.35lbs \(11.75kg\)

New Laser V3 what is changed from V2 ?

1. New Wing design improved Aileron for more precise and less drag in tip wing
2.Update Fueslage about alignment and Canopy for more smooth aerodynamic.
3.Additional Carbon plate on quick release Canopy for more nice look and fix loss covering problem
4. We change Landing gear to be 2 piece and hide landing gear for more nicely and fix often problem about loss covering. now problem about loss covering will not happen anymore.
5.New System quick release stabilizer
6.add some detail on Cowl and change spinner from 4.5" to 5"
7. improve some structure for more strong and lighter.
8. change Cowling from cover fueslage to be paste on firewall
9. add Carbon plate for cooling Canister in the bottom of fueslage.
**

LASER V3 whole design is not base from scale Laser 200

FEATURES :
NEW! Full Carbon reinforced fuselage and wing using carbon laminated wood.
Genuine German Oracover \(Ultracote\) covering
Highly prefabricated, experienced builders can have air ready in under a day
Pre-installed hinges \(glued and pinned\)
Internally mounted cowling – so no external screws exposed
Includes cooling baffles
Easy canister installation due to open construction
Removable rudder \(as well as removable wings and stabs\)
Laser engraved motor mounting position
Push-Pull system for Rudder servos

INCLUDED HARDWARE :
Complete air frame with all basic accessories \(such as carbon fibre main undercarriage, tail-gear assembly and wing-tubes as well as fibreglass control horns and wheel pants\)
Pre-installed hinges and pre-mounted canopy
Fuel tank and fuel tubing pre-prepared, fuel dot and breather valve
Wheels, axels and wheel pants
Pre-prepared pull-pull wires and pushrods with ball links
Matching carbon spinner, 5″

REQUIRED HARDWARE :
Motor: 100-130cc or equivalent electric

Servos: 7-8 high torque \(minimum 20kg\) plus throttle // Uses x2 per aileron, x1 per elevator and x1 or x2 on rudder

Also requires all the usual accessories such as transmitter, receiver, propeller, batteries, powerbox, extension leads and possibly other small accessories.

Build information :
COWL SIZE:
A: 335mm – B: 330mm – C: 307mm – D: 348mm

EXHAUST TUNNEL SIZE:
A: 603mm – B: 103mm – C: Unlimited

D: 131mm – E: 172mm – F: 192mm

Due to the open tunnel design in the Laser, there is no backplate \(measurement C\) so there is no limit to the length of exhaust that can be used.

RUDDER HORNS AND PULL PULL LOCATION:
A: 31mm – B: 55mm – C: 60mm – D: n/a – E: 8.5mm

EXTENSION WIRE LENGTHS:
Throttle : 40cm
Each aileron : 25cm + 75cm \(nearest servo and furthest servo – to reach receiver direct\)
Each elevator : 150cm
Rudder : 140cm \(when using direct – if installing pull pull, no required extension\)

CENTER OF GRAVITY : 194mm
Measured back from leading edge of the wing at the fuselage.

You will find a laser engraved C.G. emblem on the inside of the fuselage, located close to the wing tube, which also shows the exact location for Center of Gravity.